HCL - Dell XPS 13 9310 2-in-1

User Support HCL Reports
1

qubes-hcl-report

layout:
  'hcl'
type:
  'Convertible'
hvm:
  'yes'
iommu:
  'yes'
slat:
  'yes'
tpm:
  '2.0'
remap:
  'yes'
brand: |
  Dell Inc.
model: |
  XPS 13 9310 2-in-1
bios: |
  2.32.0
cpu: |
  11th Gen Intel(R) Core(TM) i7-1165G7 @ 2.80GHz
cpu-short: |
  FIXME
chipset: |
  Intel Corporation Tiger Lake-UP3/H35 4 cores Host Bridge/DRAM Registers [8086:9a14] (rev 01)
chipset-short: |
  FIXME
gpu: |
  Intel Corporation TigerLake-LP GT2 [Iris Xe Graphics] [8086:9a49] (rev 01) (prog-if 00 [VGA controller])
gpu-short: |
  FIXME
network: |
  Intel Corporation Wi-Fi 6 AX201 [8086:a0f0] (rev 20)
  1651]
memory: |
  16090
scsi: |

usb: |
  4
certified:
  'no'
versions:
  - works:
      'FIXME:yes|no|partial'
    qubes: |
      R4.3-rc1
    xen: |
      4.19.3
    kernel: |
      6.15.10-1
    remark: |
      FIXME
    credit: |
      FIXAUTHOR
    link: |
      FIXLINK

hostnamectl

Laptop: Dell XPS 13 9310 2-in-1
Operating System: Qubes OS 4.3-rc1 (R4.3)
Kernel: Linux 6.15.10-1.qubes.fc41.x86_64

dmidecode -t memory

Memory: 16 GB
Memory Speed: 4267 Mhz
Memory Type: LPDDR4

notes

  • had to add some iommu, i915 and other kernel options to get installer to even load/boot - cannot find specifics on readthedocs - I think it was mentioned in the actual installer READMEs.
  • had to disable intel software raid in bios for it to detect nvme disks
  • had to add ā€˜options snd_hda_intel power_save=0 power_save_controller=Nā€™ to /etc/modprobe.d/snd_hda_intel.conf
  • had to mess around with xsetwacom --set to ā€˜calibrateā€™ the touchscreen as I have 2nd monitor (Samsung S34J550WQE) attached via DP
  • fingerprint reader seemed recognized but have not tested it yet.
  • Performance is ā€œOKā€:
    • Run about 7 qubes, including dom0 and 3x sys-* and 1x vpn - so can handle around 2-3 additional active ā€˜big templateā€™ qubes (depending on workloads), minimal templates/lite qubes/alpine qubes are a WIP but should further improve performance.
    • Video performance is unstable - when it works it works great, but when it does not it becomes sluggish. Still troubleshooting as it was working fine but I think a recent 4.3rc1 kernel/dom0 update or grub/uefi/x11 config clobber changed something (maybe the ā€˜intel driverā€™ as it now uses modesetting) and as such recently video playback on the second monitor has become unusable - 13" laptop monitor works fine however.

Attachments

HCL-Dell-XPS-9310-2-in-1.yml (863 Bytes)

2 Likes